Página inicial/Produtos/Sensores/Sensores de força/Rotating cutting force dynamometers (RCDs), Fz max 20 kN, Mz max 150 Nm/9170A

Rotating cutting force dynamometer (RCD), Fz max ±20 kN, Mz max ±150 Nm / 9170A

Rotating cutting force dynamometer (RCD), Fz max ±20 kN, Mz max ±150 Nm
9170A
18019313
  • Rotating multicomponent dynamometer with maximum forces Fx, Fy ±5 kN, Fz ±20 kN
  • Maximum torque Mz ±150 Nm
  • Speed: max. 20000 min-1
  • Telemetric data transmission
A pedido
A pedido
Configurar
Measuring ranges
Minimum measuring range [kN]
1 kN
Maximum measuring range [kN]
20 kN
Measuring range 1, nominal Fx, Fy
-5000 … 5000 N
Measuring range 1, nominal Fz
-20000 … 20000 N
Measuring range 1, nominal Mz
-150 … 150 N·m
Measuring range 2, nominal Fx, Fy
-2000 … 2000 N
Measuring range 2, nominal Fz
-5000 … 5000 N
Measuring range 2, nominal Mz
-50 … 50 N·m
Measuring range 3, nominal Fx, Fy
-500 … 500 N
Sensitivity range 1, Fx, Fy, approximate
2 mV/N
Measuring range 3, nominal Fz
-2000 … 2000 N
Measuring range 3, nominal Mz
-10 … 10 N·m
Product type
Force sensor type
A dynamometer is a force plate measuring forces and moments.
Multicomponent dynamometer
Preloaded sensor
Preloaded sensors are already calibrated and therefore ready-to-use. Non-preloaded sensors are smaller.
Yes
Mechanical properties
Internal cutting fluid pressure, maximal
70 bar
Crosstalk
Maximum crosstalk Fx→Fy
-2 … 2 %
Maximum crosstalk Fx→Fz
-3.5 … 3.5 %
Maximum crosstalk Fy→Fx
-2 … 2 %
Maximum crosstalk Fy→Fz
-3.5 … 3.5 %
Maximum crosstalk Fz→Fx
-1 … 1 %
Maximum crosstalk Fz→Fy
-1 … 1 %
Maximum crosstalk Fz→Mz
-1 … 1 N·m/N
Maximum crosstalk Mz→Fy
-1 … 1 N/N·m
Electrical properties
Output signal type
Charge (Piezoelectric, PE)
Influence quantities
Sensitivity range 1, Fz, approximate
0.5 mV/N
Sensitivity range 1, Mz, approximate
66 mV/N·m
Sensitivity range 2, Fx, Fy, approximate
5 mV/N
Sensitivity range 2, Fz, approximate
2 mV/N
Sensitivity range 2, Mz, approximate
200 mV/N·m
Sensitivity range 3, Fx, Fy, approximate
20 mV/N
Sensitivity range 3, Fz, approximate
5 mV/N
Sensitivity range 3, Mz, approximate
1000 mV/N·m
Certificates and Standards
Degree of protection EN 60529
IP67
Operation and installation
Operating temperature range
0 … 60 °C
Speed, maximal
20000 1/min
Applications
Cutting processes and machining development
Cable properties
Cable included
No cable included
Interfaces
Connector type
M16 6 pin circular connector
Dimensions and materials
Weight
1.6 kg
Signal filter and time constants
Low-pass Filter (anti-aliasing)
3 kHz
Additional properties
Balancing class
≤2.5 G
This is a rotating four-component dynamometer for measuring the forces and torque on a rotating tool during cutting processes. Energy and measured values are transmitted on a non-contact basis, preventing wear.
A carregar
A carregar